Removing Pledge Floor Care Multi-surface Floor Finish from your wooden floor

Pledge® Floor Care Multi Surface Finish.

If you’d like to remove this product from a sealed wooden floor, please follow the steps below.

1. Mix 1/4 liter ammonia and 50 milliliters non-chlorine all-purpose cleaner into 2 liters of cool water.

2. Apply solution to a 1 square meter area

3. Soak for 3 to 5 minutes

4. Scrub with a clean sponge mop

5. Wipe up solution

6. Rinse thoroughly, changing water often

7. Dry thoroughly with a clean cloth

General Metal Polishing Instructions

General Instructions For Polishing

Suppliers of an extensive range of polishing products and accessories to professionals, retailers and the DIY enthusiast.

What is Polishing 

Polishing sometimes known as finishing, buffing or colouring is the process of removing scratches and abrasions from a surface, and creating the desired brightness of finish on that surface.  Polishing, like using sand paper, consists of procedures each of which is less abrasive than the previous. A combination of mops and compounds are used with a buffing machine or a household electric drill (pneumatic tools may also be used but only at relatively low speeds (4000 rpm max.)

Different combinations of polishing wheel and compound gives the desired cut / colouring action and finish. To avoid contamination or mixing of compounds use a different mop for each compound. Do not mix different compounds on the same mop. Alternatively “freshen” the polishing wheel with a wire brush to remove residue compound and metal from the wheel.

Alloy wheel kit

Drill mounted Polishing Kits

Drill mounted polishing kits for those small,tighter spots

 

If you are polishing small articles then you can fix your drill into a vice, this will enable you to polish these small articles with ease.

Sometimes when you have polished you may see a slight coat of grease or finger marks on the work piece, these can be removed with Whiting Powder followed by Liquid Reflection or Mirrorfinish Metal Polish to complete the job.

If you wish to Electroplate or lacquer the polished article please make sure you use a good degreaser and do not protect with wax polish. Any dirt or grease/wax will interfere with the adhesion of the plated metal or lacquer.

Surface Polishing Preparation 

Unclean/dirty/greasy material should be prepared properly before being polished. For polishing soft metals and depending on the surface condition, start at 6 on the step by step guide above. Should parts be heavily scratched, marked or scored then suitable abrasives should be used.( flap wheel, abrasive cloth/paper, rubbing blocks etc. )

In many instances the surface of what you are polishing will need to be prepared prior to polishing. The preparation really depends on the condition of the surface and the desired finish you require. The devil is in the detail hence the better you prepare the surface the better the final result. The use of wet/dry abrasive papers and discs may be required and the finer the abrasive, generally the easier and more impressive the polished finish.

Drill-Polisher-Grinder AdaptorsPolishing Wheel Spindle Adaptor Kit

Spindle adaptors, tapered Mandrels are used to secure your polishing wheels onto your drill machine, bench grinder, variable speed polisher/grinder etc.

Before purchasing an adaptor check the dimensions of the shaft and threads to see if we have the relevant adaptors for your machine.

Description Of  Polishing Wheels & Mops

Sisal Polishing Wheel.

These are very fast cutting and hard, they are particularly useful for first stage heavy duty mopping operations on steel and non-ferrous metals. They will remove grinding marks left from previous operations, when processing steel, stainless steel or non-ferrous metals and are usually used in conjunction with a coarse cutting stainless steel polish.

Colour Stitch     

White Stitch Polishing Wheels.

Versatile cutting mops used for general polishing, can be used for first stage polishing with Brown polishing compound on soft metals (brass, copper, etc), or for second stage polishing on hard metals with Pink polishing compound.

Loose Flap Quality Polishing Wheel.

A harder grade of loose mop which is commonly used as an alternative to white stitch mops. Very popular for precious metals.

Swansdown (WDR) Polishing Wheels

A very soft grade of finishing mop. WDR means “white double raised” and these wheels are also know as Swansdown wheels. Generally used for soft precious metals, jewellery etc. in the final finish.

Airflow Treated and Untreaded Polishing Wheels

Quality materials are used in the manufacture of these wheels, ensuring a longer mop life and greater output compared with conventional mops. They are very clean in operation and are specially suited for heavy duty moping and finishing on metals, plastics and other non metallic materials. The treated Airflow wheels are more aggressive and used in the cutting, first stage of polishing whilst the untreated airflows are for finishing.

Dome Cylinder Goblet Polishing Wheels

Supplied in sisal and calico these drill mounted polishing mops are used to access tight and difficult to reach areas.

Excellent for use in maintenance kits, the calico mops can be used with most of our compounds.  The sisal mops can effectively be used with our cutting compounds.

Mounted Felt Cylinder Bob

Versatile across many mediums, these medium density points will work on stone, ceramics, metals, as well as jewellery. Bonded onto a 3mm/6mm shaft that fits most rotary tools or drill machines. These felts tools are a popular and economical method of polishing when used in conjunction with compounds.

Safety First!

Always make sure that the machine you are working with is in safe working order i.e. bench grinder is securely fastened to your work bench, adaptors polishing wheels are securely fastened etc.

Always use safety equipment- Dust mask, safety spectacles and gloves should be worn at all times. 

Always apply the item being finished to the area of the mop which is rotating away from yourself.

Do not wear loose clothing that may get caught in the machine.

SS Polishing Kit

Restoring Stainless Steel Sinks

Kits to revitalise your scratched sink to a high new finish.

Step By Step Guide To Polishing

  1. 1. Attach arbour to your drill or spindle adapter to your bench grinder / polisher and fix tightly.
  2. 2. Attach Sisal Mop onto the arbour/adapter and screw on tightly.
  3. 3. Run the drill / bench grinder / polisher and apply the relevant compound to the sisal mop for approx. 2 seconds, the compound is wax / abrasive based so the motion of the spinning mop generates heat which melts the wax/abrasive onto the polishing mop.
  4. 4. Apply the mop to the item to be polished with medium/hard pressure. It is very important that you remove all marks/scratches and leave a uniform finish.
  5. 5. Apply more compound to the Sisal Mop if needed. When all scratches/marks are removed and the work piece has a uniform dull finish, remove the Sisal polishing mop.
  6. 6. Attach the White Stitch / Colour Stitch Mop onto the arbour/adapter and screw on tightly. Run the machine and apply the relevant compound to the White Stitch / Colour Stitch Mop for approx. 2 seconds.
  7. 7. Apply the mop to the item to be polished with medium pressure. This will remove the dull finish left by the first process and leave the work piece with a semi-bright finish.
  8. 8. Apply more compound to the White Stitch / Colour Stitch Mop if needed. When you have a uniform semi-bright finish, remove the White Stitch / Colour Stitch Mop.
  9. 9. Attach either the unstitched B Quality Mop onto arbour / adapter and screw on tightly.

Run the drill / bench grinder / polisher and apply the relevant compound to the unstitched B or G Mop for approx. 2 seconds.

  1. 10. Apply the mop to the item to be polished with light pressure. This will remove the semi bright finish left by the second process and leave the work piece with a bright finish. Apply more compound to the unstitched Mop if needed and repeat the process.

You should now be left with a bright finish.

  1. Using a clean microfiber cloth, rub the polished article with Whiting Powder/Vienne Lime or Liquid Reflection, Reflection paste or Blue Sapphire. This will remove any residue compound, metal and grease left on the surface and provide you the polished finish.

Tips 

Try to constantly vary the directions of which you polish. This is not always possible but recommended as some articles may be of an unsuitable size and shape.

Use compound sparingly, black grease marks will appear on work piece if too much compound has been applied to the mop. Remove black grease marks with cloth. Remember little and often. If it is possible, polish across marks/scratches not along them.

If the surface of work piece is lacquered you must remove the lacquer before polishing.

Description Of Polishing Compounds

There is a substantial range of cutting, polishing, buffing compounds suited to different levels finishes depending on the polishing wheel and compound combinations.

  

Blue bar = Multishine: The multi-purpose finishing compound. Suitable for all metals. Also performs well as a cutter if used on a hard cotton or sisal buff.

Brown bar = Tripoli: Combined cutting and finishing compound for soft metals only. Suitable for alloys, aluminium, brass, copper and zinc diecast. Follow up with a finishing compound if a brighter surface is required.

Grey bar =Course Cutter: A fast and economical cutter for hard metals. The rate of metal removal is high, with less emphasis on brightness. To be used on sisal buffs for the removal of scratches and “orange peel” from all metals.

Green bar = green Chro

me: For mirror finishing with minimal cut. Best used after a perfect cutting or prepolishing operation. Polishes all metals to high brightness when used on a soft cotton buff.

White bar = SS Finish: For high brightness and good cut. Suitable for all metals, including stainless steel. Recommended for surfaces that are smooth to begin with and are free of deep scratches. Use a sisal buff for cutting and a cotton buff for bright finishing.

Terracotta bar = Bright Cut DX:  A fast cutter for all metals with medium brightness. May be used on a sisal buff for cutting, followed on a cotton buff for medium brightness.

Vienne Lime Cleaning Powder Or Whiting Powder: Excellent for use with our polishing kits. Use this after you have finished polishing to remove grease and compound residues after polishing. Apply it to a clean lint free cloth/microfibre and wipe where you’ve been polishing. Please note that Vienna Lime is not an actual lime powder but a pure form of super fine calcium carbonate (chalk). This will save you time and effort as opposed to using white spirit or other methods.

Liquid Reflect, Blue Sapphire, Mirrorfinish metal polishes and many others are used in your final application to maintain a long lasting bright finish to your polished surface. These polishes can be used in the maintenance of your polished items as well.

Surface Preparation Abrasives

Flap wheels are designed to be flexible and conform themselves to the shape being sanded. Flap wheels flex to the different dimensions and shapes of the work piece and sand flat, high and low areas with the same effectiveness. Surfaces include wood, metal, plastics, rubber, stone. Wet and dry abrasives up to 2000grit are ideal for the surface preparation of most metals and can be used before moving onto the buffs and compound combinations.

Visit our website at www.polishup.com.au to view a wide range of products and services that include the following applications:

Kits to polish glass, metals including alloys, aluminium, chrome, stainless steel, steel, copper, brass, precious metals and jewellery

Australia based, we ship Australia wide and internationally.

You can polish your motorcycle, golf clubs to new, car, truck, ute, boat, alloy wheels, fixtures and fittings to exceptional mirror finishes. The polishing wheels fit bench grinders, electric hand drills, polisher sander grinder machines. Choose from our selection of adaptors and accessories for a simple conversion.

Spindle adaptor kit  98315 2 e1571117129867

Polish Up’s Polishing Adaptors & Accessories

Tapered Spindle Adaptors

If you have a standard bench grinder or polisher and you are wanting an adaptor to fit the various polishing wheels then choose one of our range. We’ve a selection to fit most workshop machines.

M14 Polisher AdaptorPU scaled 1

M14 Threaded Tapered Spindle Adaptor

Most rotary type polishers that come with a 180mm backing pad and usually have an M14 threaded spindle. Our tapered spindle is perfect for this type of application:

Drill Adaptor2 e1570139730162

Tapered Drill Adaptors

Ideal for the small wheels and used with your drill machine. 100mm diam wheels would be the go with this adaptor. Having a 6mm shaft your polishing wheel screws on or is unscrewed and changed within seconds.

Drill mount4  19729 4

Bench mount drill clamp

Does what it says on the tin. You can secure you drill machine in this vice and use our tapered drill adaptors to make a polishing machine.

Kit Spindle Adaptors  94445

Bench Grinder Spindle Adaptors

If you have a bench grinder that you want to adapt as a polisher a couple of things need to be done:

Check on the machine spindle size to ascertain which are the correct adaptors to purchase.
Check on the strength of the machine to choose the correct wheel size. Too large and they’ll be cumbersome for the machine to handle. The machine will slow down when you hold an object against it. Need advice give us a call on 1800 780 666.

M14 Drill 8mm Shank Adaptor For Electric drill/Polishing pad

8mm to M14 thread adaptor

Using a backing pad with your drill machine? this adaptor is made for the job.

M10 to M14 Adaptor copy  06966

M14 to M10 adaptor

Some of the smaller polishers or grinder have an M10 thread. This is great for the backing pad that has an M14 thread.

bumpers

Forever Black Car Care Products

Forever Car Care Products (FCCP) uses specially formulated dyes instead of silicone to bring back the life to faded black bumpers, trim, tires, bed liners and more! …and they hold the color much longer and help protect against environmental elements such as UV rays. What’s more, Forever BLACK™ products do not pick up or attract road grime or dust!

Environmental elements can be damaging to any vehicles, fading, black trim, bumpers, tires, bed liners, and other exterior parts. FCCP revive the appearance of plastic, rubber and vinyl while protecting against harsh UV rays.

Forever BLACK™ Tire Gel

Forever BLACK™ Tire Gel, unlike all other tire dressings on the market, is a black pigmented polymer. Restore the faded bronze look of your tires to a rich black luster. Say goodbye to messy sprays! Our handheld applicator eliminates the mess of oversprays. You’ll be amazed! One easy application will protect and restore your tires to their original brilliant appearance.
    5
Forever black tyre gel

Posted by Ricky

Great product…

  •     4
    Forever tire gel

    Posted by Mike Hayward

    Great product coverage good just a shame it’s a matt finish.

  •     4
    Forever black Tyre gel

    Posted by Glen palmer

    Covers and lasts a long time, shame it doesn’t have more of a gloss

Forever BLACK™ Black-Top gel

Forever BLACK™ Black-Top gel will rejuvenate your faded sun-damaged tops (vinyl, convertible, bimini and soft tops) to a rich black luster. This environmentally friendly, silicone-free, black-pigmented polymer will keep your vehicle in tip “top” condition. With built-in UV protectants, Black-Top gel will protect your top from further sun damage.

Forever BLACK™ Truck Bed Liner Gel

Forever BLACK™ Truck Bed Liner Gel gives your bed liner a new look with one easy application. This silicone-free gel restores your liner’s rich luster. The non-slippery surface can last at least 6 months under normal conditions.

Forever BLACK™ Bumper & Trim Cleaner and Reconditioner

Forever BLACK™ Bumper & Trim Cleaner and Reconditioner has become America’s #1 choice for restoring black bumpers & trim. Permanently recolor and protect all black plastic, vinyl & rubber surfaces on your car without silicone. We use the same chemicals that the manufacturers use. This product does not attract dust. Protects against U.V. damage.

Reviews

“Ok, your Forever BLACK Bumper & Trim Reconditioner is about the greatest thing I have ever found for use on a car or truck. The Forever BLACK Bed Liner Gel also worked very well on my spray-in Rhino liner. Thank you for all of your help, support and for being part of such a great product!”

Russ, South Carolina

“We own a 1991 Honda. The paint was failing and my wife was lobbying for a new car. However, the car still drives great. We decided to get a paint job. Once we had the car painted, the side moldings and bumpers looked really bad – mottled and gray. My wife googled and found your product. It really made a difference. We used the Forever BLACK Bumper & Trim Reconditioner and now the car looks like its brand new. I liked the Bumper & Trim Reconditioner’s applicator for spreading the product around. It was easy to control and to achieve an even finish. So, with your help our old car looks new again and I’m not making car payments! I’m glad we found you!”

Bill, Louisiana

“I recently purchased some Forever BLACK Bumper & Trim Reconditioner for my wife’s car. The vinyl was very faded and going white. After applying the Bumper & Trim Reconditioner it has transformed her car. I was amazed with the results. I have used many vinyl treatments, but this beats them hands down. I will recommend your products to everyone!”

Ryan, Republic of Ireland

“I recently used the Forever BLACK Bumper & Trim Reconditioner on a 21 year old Renault 5. I wasn’t sure if it would work as the bumpers and side trims were faded to white. After a few applications, the car looked brilliant and all of the plastic bumpers and side panels looked like new. I have had neighbors asking if I have had the car professionally restored – that’s how good it looks! I just wanted to say what a great product this is and I have and will continue to recommend this product to everyone I know.
Thanks very much for an item that does exactly what it says it does on the bottle.”

Michael, via email

  •     5
    Forever Black

    Posted by John 

    Man this stuff is fan-fucken-tastic!!
    It’s so easy to apply
    A little goes along way
    Dries almost instantly
    Transformed all the faded and cracked window rubbers
    and trims to like new finish
    Totally black after use
    Highly recommend!!

  •     4
    Pleasing to the eye

    Posted by Unknown

    Great product, just ensure you prep the surface area very thoroughly. Also recommend taping off the area to be treated, especially if you don’t have a steady hand.

  •     5
    Satisfaction

    Posted by Unknown 

    Have not used latest purchase, but have used same product for 15 yrs and am satisfied with the end finish.

Cabinet Makers Wax1  80738 e1561507625222

Goddard’s Cabinet Makers Polish

Goddards Cabinet Makers Wax Liquid Furniture Polish (473ml) 

Wood will lose its natural beauty from exposure to sunlight, dirt buildup and cleaning with abrasive chemicals.  To prevent damage, treat your wood furniture with Goddard’s Furniture Polish.
  • Conditions and Protects with Lemon Oil and Beeswax.
  • Lasting Shine with No Oily Residue.
  • Cleans and Shines Wood to a Deep Luster.
  • Quick and Easy to Use with No Rubbing or Buffing.
  • Protects Against Sun Damage, Stains, Drying and Cracking.

The heritage of Goddard’s wood care was built on over 100 years of demonstrated performance.  Professionals and respected establishments continue to trust Goddard’s Furniture Polish for the finest wood furniture.

Goddard’s Furniture Polish in the easy-to-use spray is perfect for a clean shine on wood furniture that gets regular use.  The spray dispenses a larger amount of the active protectant for a deep shine, which will protect against damage from sunlight, stains, drying, cracking and everyday wear and tear.

Directions

  • SHAKE WELL.
  • Hold bottle 6 inches from surface and spray over the entire area.
  • Wipe immediately along the grain with a clean, soft cloth, turning occasionally.
  • For small items and hard-to-reach surfaces, spray product directly onto cloth and wipe.
  • Heavily soiled surfaces should be cleaned prior to using polish.

Goddard’s Cabinet Makers Wax Polish 4OZ 

Wood will lose its natural beauty from exposure to sunlight, dirt buildup and cleaning with abrasive chemicals.

  • Conditions and Protects with Lemon Oil and Beeswax.
  • Lasting Shine with No Oily Residue.
  • Cleans and Shines Wood to a Deep Luster.
  • Helps Conceal Scratches, Rings and Dull Spots.
  • Revives Rough, Old Finishes

The heritage of Goddard’s wood care was built on over 100 years of demonstrated performance. Professionals and respected establishments continue to trust Goddard’s Cabinet Makers Wax for the finest wood furniture.

Goddard’s Cabinet Makers Wax can be used on wood cabinetry, furniture, paneling, doors, trim and more. The low-odor polish conditions and revitalizes, and leaves no residue or powder. This product enhances the appearance of color and grain patterns in wood without leaving a greasy or oily finish. It can be used on all types of wood including solid, laminate and composite.

Directions

  • Apply wax sparingly with a clean, dry cloth.
  • Rub out evenly.
  • When dry, polish lightly with a separate clean, soft cloth, turning occasionally.
  • Buff to an even shine.
  •     5
    Best Furniture Polish Ever

    Posted by Unknown 

    Simply the best furniture polish, and so easy to use. Wonderful on antiques, leaving a beautiful finish. All Goddard’s products are guaranteed to give exceptional results.

  •     5
    Simply the best

    Posted by Uncle Bernie

    I have used this product for many years it is perfect for antique furniture and so easy to use delivering a first class finish every time with minimal effert

        5
    madenson@slingshot.co.nz

    Posted by Michelle Denson 

    Excellent polish. All my friends want it so will have to order more. Also excellent customer relations. Was out of stock but rang me and kept me informed all the way.

        5
    Goddards Cabinet Makers Wax Paste Furniture Polish

    Posted by PRH 

    The wax was easy to apply and gave a high quality finish to my timber stand. The instructions enclosed were easy to understand and follow which made the process easy and a positive experience.

Wooden Furniture scaled 1
10jewelryCleaner  08919

Goddard’s Jewellery Cleaner Care Kit

Goddards Jewelry Cleaner Care Kit 

Dirt, tarnish and grime will make the appearance of jewelry less attractive and dull. Keep your jewelry clean and beautiful with the trusted performance of Goddards Jewelry Cleaner.

  • Instantly Cleans and Shines.
  • Dissolves Tarnish and Dirt.
  • Safe for All Precious Metals and Stones.
  • Ammonia Free.
  • Dipping Basket and Brush Included.

The original jewelry cleaning formula developed by Joseph Goddard has been perfected over time by combining traditional excellence with today’s advanced technology.  Goddards Jewelry Cleaner continues to utilize that high-quality jewelry cleaning formulation to provide trusted cleaning performance.  Give your jewelry the royal treatment with Goddard’s Jewelry Cleaner.

Directions

  • Dip jewelry into cleaning solution and soak for two minutes.  For small articles, use dipping basket.  For larger articles, pour Goddards Jewelry Cleaner solution into a bowl.  For the best results, brush embedded dirt from jewelry with the enclosed brush.
  • Rinse article in water and dry with a soft, clean cloth.  The Goddards Cloth is recommended for drying.  It will provide your jewelry with an added layer of protection against tarnish.
  •     5
    Sparkling

    Posted by Catherine Guiffrida 

    My order arrived the next day….I couldn’t believe it.
    The product is so good that I ordered one for my daughter, one for my daughter in law and one for my self.
    Need I say more????

  •  
  •     5
    Great Delivery

    Posted by Sue 

    Good morning Rex,

    My order arrived this morning, thank you! I am most impressed with your service – I placed my order, paid, it was dispatched & I received it all in under 24 hours. I sincerely compliment you.

  •  
  •     5
    Great Jewellery Cleaner

    Posted by Peter

    This stuf is brilliant.Does a fantastic job of cleaning all Jewellery and plated items. Its quick and easy to use, producing a fantastic shine and sparkle. You can certainly tell the difference. We just tip a little into a separate bowl and after cleaning you’ll see just how dirty some items get from day to day wear, looking at the used liquid. Don’t bother looking in the major supermarkets, they stopped selling this stuff over a year ago.

Polished Bike1 copy scaled 1 11zon

Alloy, Stainless Steel Metal Polish Called Blue Sapphire

Liquid and Paste Blue Sapphire

If you are looking for a clever polish that’ll give you a brilliant finish and make your metal surface resonate then this is the polish. Using nano technology, this product has been designed for bikes mainly but can also be used on an extensive variety of metal surfaces. The results will speak for themselves and will definitely be money well spent.

Try it!

Blue Sapphire are metal polishes that impart the same brilliant shine as Liquid Reflection, however it is designed for detailed and intricate surfaces such a motorbike chrome or antiques. After polishing Blue Sapphire dries to a fine powder that is easily brushed or vacuumed off, leaving no residue to adhere to the surface. High pressure air can also be used to blow out left over polish caught in tight nooks and crannies.

Blue sapphire is recommended for Chrome trim over Liquid Reflection as the abrasive is a little finer.

Reviews 

   5
Ultimate Match

Posted by vicki

This product when used after the tinned product really is a perfect match. Never have I seen such an amazing mirrored showroom finish after using these outstanding products. Thankyou Polish Up ! customer for life

    5
Best Polish Ever

Posted by vicki

This product in my opinion really is the best for deep cleaning metals particularly alloy. No shortcuts with cheap imitations will I take again. Definitely a winner in my book.

    5
Blue Sapphire polishing paste

Posted by Col

Product worked better than expected would highly recommend

Cerium Oxide Glass Polish | Polishing Glass

Polish Up Microfiber Cloths

400 x 400mm Microfibre Polishing Cloth

Microfiber cloths are used for cleaning and polishing, are generally constructed from split conjugated fibers of polyester and polyamide.  They can hold up to seven times there weight in water and have exceptional ability to absorb oils, and are not hard enough to scratch even paintwork.

These Microfiber cloths require no cleaning fluid. Ensure that your microfiber cloth is clean and not retaining any grit as it will scratch the surface you are polishing.

They must only be washed in regular washing detergent, not oily, self-softening, soap-based detergents. Fabric softener must not be used. The oils in the softener and self-softening detergents will clog up the fibers and make them less effective until the oils are washed out.

The following diagram illustrates the efficiency of microfiber cloths as opposed to cotton or other cloths. (Information provided by Wikipedia)

Reviews

5
Quality Microfibre

Posted by Co from Quialigo

You get what you pay for !! Remember that when you consider a cheap pack of microfibre from other suppliers. These are top quality and you will know that when you use them because they do what microfibre should, especially when drying smooth surfaces like glass or polished bench tops.

    5
Quality vs Price

Posted by Unknown

There are cheaper options available, but I found the microfibre cloth from Polish Up to be higher quality and you will notice this when it comes to using them. Be aware of quantity packs at what will seem to be “a good price”. You get what you pay for!!

Brass Copper polish scaled

Goddard’s Long Term Brass and Copper Polish

Goddards Long Term Brass and Copper Polish

"I can see things on these articles which I have been unable to see because other cleaners did not perform like Goddard's Brass & Copper Polish."

Goddards Long Term Brass & Copper Polish 210ml Bottle

Goddards Brass & Copper Polish helps protect and restre the natural beauty of brass and copper.  It has a long term formulation that provides a longer lasting shine.  It also helps brass and copper look tarnished free and bright for longer.  Its non abrasive and very easy to apply using a soft cloth.  

All metals are vulnerable to tarnishing, especially brass and copper.  When in need of an all-purpose metal polish, rely on the trusted performance of Goddard’s Brass and Copper Polish.  

  • Removes Toughest Tarnish with no Rubbing or Buffing.
  • Provides Anti-Tarnish Protection.
  • Use on Metals Such as Brass, Copper, Chrome, Aluminum, Pewter and more. 

Use Goddard’s Brass and Copper Polish to bring out the natural beauty of your fine metal.  The expert formulation of Goddard’s Brass and Copper Polish is safe for all household metals, including those that are in contact with food.  

Directions

  • SHAKE WELL BEFORE USING.
  • Apply polish with clean, soft cloth until all tarnish is removed.  Turn cloth frequently to avoid re-using soiled portion of cloth.
  • Allow polish to dry.  Wipe with clean, soft cloth.  For ornate objects, rinse polish off with wet sponge.  Dry.

Reviews

  •     5
    best polish

    Posted by Unknown

    Excellent results and long lasting. I also use silver foam and love it.

  •     5
    Brilliant product

    Posted by Marion

    Gentle and effective, easy to use. Takes all the hard work out of cleaning precious and detaied items.

  •     5
    Wonderful product

    Posted by Unknown on 1st Jan 2015

    My mother and grandmother used Goddards for good reason..they work instantly and last a long time. So glad to have rediscovered this product on line, well worth buying and using if you want to do a cleaning job that actually lives up to it’s name.

  •     5
    Great Stuff

    Posted by Unknown 

    Have tried other brass polishes but this was by far the best brass polish I have ever used

  •     5
    Only the best.

    Posted by Unknown

    Goddards Long term Brass and Copper Polish cleans and shines wonderfully, and the shine does last much longer.

  •     5
    Brass and copper polish

    Posted by Brenda Sperling

    A very good product. Easy to use, good finish.

  •     5
    Brass & Copper Polish

    Posted by Pat Brown 

    Excellent polish which is easy to use, and economical too. My brass articles are looking brilliant. I can see things on these articles which I have been unable to see because other cleaners did not perform like Goddard’s Brass & Copper Polish. The picture on the label is just how my brass goods are looking. Thank you Goddard’s.

  •     5
    Brass and Copper Polish

    Posted by Susan Bradley 

    This product is astonishingly good! I used it to clean a heavily tarnished musical instrument of unlacquered brass. The tarnish just vanished as soon as the product was applied, and after drying, revealed a lovely soft warm shine. Very good indeed.

  •     4
    tarnishing

    Posted by Peter James 

    No only is it great for cleaning it prevents the brass from tarnishing and reduces the times of recleaning.

  •     5
    Great Product.

    Posted by Unknown 

    Easy to use excellent result.

  •     5
    Magic – effortless

    Posted by ch 

    A quality product that shows in the ease of use and end result – brilliant long lasting lustre – highly recommended. A product name remembered from my childhood for its quality.

     

Brass Trumpet scaled 1
Polishing Compound for Plastic | Plastic Polisher

Polish Clears & Plastics with Novus Compound Kits

Novus Compound Kit 237ml NOVUS Auto Glass – plastic polish restores original beauty to all plastic and acrylic products. Since 1973, NOVUS Auto Glass plastic polishes have been used around the world to restore the shine and brilliance to many types of plastic acrylic surfaces. It is truly a product that once you use it, you will wonder how you ever got along without it! NOVUS Auto Glass is the answer to scratch removal and long lasting protection for all plastic, acrylic and fibreglass products. For home or industrial use, NOVUS has formulated a complete system to restore scratched, faded or discoloured plastic materials. The NOVUS Plastic Polish 1, 2 and 3 polishes provide a complete system of scratch removal and surface restoration when used together NOVUS Plastic Polish 1 can be used individually to clean, shine, and protect all types of plastic surfaces. NOVUS Plastic Polish 2 keeps plastic looking new by removing fine scratches and haziness. When damage is more severe,NOVUS Plastic Polish 3. NOVUS Plastic Polish 3 removes heavy scratches and abrasions and is formulated to prepare the surface for no. 2 polishing. Since NOVUS Auto Glass technology introduced its plastic polishes 1973, simple techniques have added new life to plastics and acrylics with easy-to-achieve professional results. The three NOVUS Auto Glass polishes are helping millions win the war against fading, scratching and dulling of plastics that all too often cause the best products to grow old before their time.

HERE ARE JUST A FEW USES FOR NOVUS POLISH

DVD’s, Video Games, CD’s Auto Interiors, Gauges, Chrome, & Acrylic Paint Microwave Oven Doors, Decorator Acrylic Refrigerator Panels Motorcycle Windscreens, Visors, Fairings & Helmets Snowmobile Windshields, Helmets, & Hoods Acrylic Hot Tubs & Spas Boat Windows & Fiberglass Salad Bar Sneeze Guards Emergency Vehicle Light Bar Lens Covers Plastic Storm Windows & Skylights Collapsible Windows on Convertibles & Sport Utility Vehicles Turntable Dust Covers, Stereo Faceplates Acrylic, Fiberglass or Cultured Marble Tubs, Showers & Counters Acrylic Aquariums Telephones, Pagers, Scanners Acrylic Trophies & Awards Plastic Display Cases & Signs Gauges & Instrument Control Panels Safety shields & Goggles Airplane Windows Video Games, Pinball Machines & Jukeboxes Copiers and Fax Machines Acrylic Furniture Cash Registers & Calculators Acrylic on Tanning Beds POLISH TIPS

Power Buffer

If the damaged area is fairly large or badly damaged, a power buffer may be used with NOVUS No. 2 and No. 3. Use a clean cotton bonnet and operate the buffer at a low speed to avoid overheating the plastic, approximately 1,000 RPM. Each polish should be applied with a seperate, clean bonnet.

Before Polishing

Before attempting to clean or remove scratches, always make sure the plastic is cool to the touch. Use a liberal amount of plastic cleaner to safely remove surface dust and dirt. In addition, test scratch removers in a small or inconspicuous area for compatibility.

Coated Plastics

Some plastics are coated with a thin film which may be damaged by the abrasives in the polish. NOVUS No. 2 and No. 3 Polishes are not recommended for use on coated plastics or eyeglass lenses.

Polishing Cloth

The type of polishing cloth you use will make a difference. The ideal cloth is nonabrasive, absorbent and lint free. To eliminate any chance of scratching, use only disposable cloths. Reusable cloths can retain abrasive particles, but you won’t know for sure until the damage is done. Use a soft cotton cloth (such as a diaper), avoid using polyester or rayon wipes which can scratch unprotected plastics.

FINE SCRATCH REMOVER

Removes fine scratches, haziness and abrasions from most plastics. With repeated use, NOVUS No. 2 restores faded and discolored plastics. Removes the damage instead of filling it in Buffs out quickly After restoring, seals with a coat of polish Observe condition of the surface to be treated. The deeper the scratches, the greater the pressure required to remove them. If the surface is dirty, clean with NOVUS No.1 before applying NOVUS No. 2. Shake well. Test in an inconspicuous area. Apply NOVUS No. 2 liberally. Using a clean, soft cloth, polish with a firm back-and-forth motion at right angles to the scratches. Keep the cloth saturated with polish at all times. When the worst scratches have been polished out, reapply NOVUS No.2 uniformly in a circular motion to the entire surface using short, circular strokes and light pressure. Allow to dry to a light haze. Using a clean portion of the cloth, buff the surface to a slippery glaze using firm, short strokes. This procedure is imperative in achieving the best results. For heavy scratches, multiple applications of NOVUS No. 2 or application of NOVUS No. 3 may be required. Follow with NOVUS No. 1 for best results.

PLASTIC CLEAN & SHINE

Gently cleans all plastics without scratching. Leaves a lustrous shine that resists fogging, repels dust, and eliminates static. Resists finger marking Contains no abrasives or harsh chemicals Leaves a smooth, clean, greaseless shine If the surface is extremely dirty, apply NOVUS No. 1 liberally and wipe using long, sweeping strokes. Do not use pressure at this time or large dirt particles may scratch the plastic. Re-apply NOVUS No. 1. Polish using short, circular strokes with a clean portion of the cloth. When surface is thoroughly clean and uniformly covered, buff to a slippery glaze with a clean portion of the cloth. Surfaces buffed to a high glaze are more resistant to dust and future scratching. Reapply NOVUS No. 1 regularly to maintain the antistatic, smudge and scratch resistant properties.

HEAVY SCRATCH REMOVER

Removes heavy scratches and abrasions from most acrylic surfaces. Use when damage is too severe to be restored with NOVUS No. 2 polish. Requires use of NOVUS No. 2 for final finishing Not recommended for use on coated plastics Shake well. Test in an inconspicuous area. Apply NOVUS No. 3 liberally. Using a clean, soft cloth, polish with a firm back-and-forth motion at right angles to the scratches. Keep the cloth saturated with polish at all times. Continue polishing until only fine scratches remain. Using cloth, remove all remaining polish, this is very important! Using a clean cloth, apply NOVUS No. 2 in a circular motion uniformly to entire surface. Polish using light pressure until NOVUS No. 2 dries to a light haze. Using a clean portion of the cloth, buff the surface clean. Follow with NOVUS No. 1 for best results.

3 x NOVUS PREMIUM POLISH MATES

This microfilament cloth is perfect for polishing. Highly absorbent, extra durable and abrasion resistant makes this washable cloth the ideal solution. The type of polishing cloth you use will make a difference. This ideal cloth is nonabrasive, absorbent, and lint free. To eliminate any chance of scratching, use only disposable cloths. Reusable cloths can retain abrasive particles, but you won’t know for sure until the damage is done.

Reviews

    5
Novus Compound Kit (small)

Posted by Bob

I got a nasty scratch right across two polycarbonate windows and the door on my new caravan. I used the product as the directions indicated and can now not find the scratch.

    5
Novus 2

Posted by Bob Piper

We do a lot of pen making in the Men’s Shed and this is the best product I have found for final polishing of acrylic pens. Produces very high sheen

    5
Novus Scratch Remover on Caravan Windows

Posted by Bob

I used Novus Fine Scratch Remover 2 to remove scratches on my off road caravan windows. It is easy to use and very effective.

    5
Money saved.

Posted by Unknown

I have done the repair saving over $640 for a new headlight thanks

    5
When you need it to be sparkling

Posted by Adrian

This is the best acrylic polish I have found. It gets all kinds of things off and leaves a mirror shine.

Really great product.
    5
Novus 3

Posted by Bob Piper

Excellent for removing sanding marks in preparation for final polish

    5
Novus Compound Kit (small)

Posted by Bob

I got a nasty scratch right across two polycarbonate windows and the door on my new caravan. I used the product as the directions indicated and can now not find the scratch.

    5
Highly recommended

Posted by Scott

Hey just a note to say that I recently purchased the Novus polishing kit and it is awesome…..highly recommended. Regards Scott, BE Mech

    5
Those paper type polishing cloths are awesome

Posted by Roger Morrison

Hi guys,

Great product, it removed the small scatches I put in my new BMW motorcycle screen….a bit of grit in a mircofibre cloth polishing at night after a couple of beers will do that! What is outstanding is those polishing cloths….sort of like a paper type material….anyway I musrt be impressed I just bought another 50 of them. Cheers Roger

Save you Time: Here are some links to kits

Search for products

Back to Top
Polishup